Patton electronic Network Card 3P MF9 User Manual

USER

MANUAL

MODEL 3P-MF and

3P-MF9

DB-25 and DB-9

In-Line Power

Supply Adapters

Part# 07M3PMF9 Rev. B

Doc# 056020U

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Revised 5/29/03

An ISO-9001

Certiﬁed Company

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 3P-MF Series components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the ﬁrst date of shipment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modiﬁcation. If this

product fails or does not perform as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronics be liable for any damages incurred by the use of this

product.These damages include, but are not limited to, the following: lost

proﬁts, lost savings and incidental or consequential damages arising

from the use of or inability to use this product. Patton Electronics spe-

ciﬁcally disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Models 3P-MF and 3P-MF9 generate and use radio frequency

energy, and if not installed and used properly—that is, in strict accor-

dance with the manufacturer's instructions—may cause interference to

radio and television reception. The Models 3P-MF and 3P-MF9 have

been tested and found to comply with the limits for a Class A computing

device in accordance with the speciﬁcations in Subpart J of Part 15 of

FCC rules, which are designed to provide reasonable protection from

such interference in a commercial installation. However, there is no guar-

antee that interference will not occur in a particular installation. If the

Model 3P-MF or 3P-MF9 do cause interference to radio or television

reception, which can be determined by turning the power off or discon-

necting the RS-232 interface, the user is encouraged to try to correct the

interference by one of the following measures: moving the computing

equipment away from the receiver, re-orienting the receiving antenna

and/or plugging the receiving equipment into a different AC outlet (such

that the computing equipment and receiver are on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates that it is

in compliance with the Electromagnetic Compatibility (EMC) directive

and the Low Voltage Directive (LVD) of the Union European (EU). A Cer-

tiﬁcate of Compliance is available by contacting Patton Technical Sup-

port.

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Service at

(301) 975-1007, http://www.patton.com, or [email protected].

Note Packages received without an RMA number will not be

accepted.

Patton Electronics’ technical staff is also available to answer any ques-

tions that might arise concerning the installation or use of your Model 3P-

MF Series product. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This

product has been thoroughly inspected and tested and is warranted for

One Year parts and labor. If any questions or problems arise during

installation or use of this product, please do not hesitate to contact Pat-

ton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• Solves low power interface problems

• Provides power to any Patton self-powered short-range modem

• Supplies 9 VDC to pin 9 (DB-25 and DB-9)

• DB-25 male to DB-25 female connectors (Model 3P-MF)

• DB-9 male to DB-25 female connectors (Model 3P-MF9)

• LED indicator shows power status

• 120 or 230 VAC versions available

• Very thin case (0.7 in./1.8 cm) for closely spaced computer ports

• Nothing to conﬁgure—just plug it in!

2.2 DESCRIPTION

The Model 3P-MF Series power supply adapters let you use any Patton

self powered short haul with an underpowered EIA-232 or EIA-574 inter-

face. Many laptops, notebooks and PC cards on the market supply inter-

face that’s well below the speciﬁcations of the actual standard. The

Models 3P-MF (DB-25 connectors) and 3P-MF9 (DB-9 connectors) can

easily bridge that gap. Special versions also available.

Model 3P-MF is equipped with DB-25 connectors on each end; Model

3P-MF9 has DB-9 connectors. Each provides 9VDC to Patton’s interface

powered short hauls on pin 9. And both 120 VAC and 230 VAC wall-

mount adapter versions are available.

3.0 INSTALLATION

Patton's Model 3P-MF Series are easy to install and should give you

years of trouble-free service. Here are a few simple instructions to help

you get things hooked up right. If you have any questions, please contact

Patton Electronics Technical Support at (301)975-1007.

1. Disconnect the short haul modem from the low-power EIA-232

device.

2. Connect Model 3P-MF/3P-MF9 into the DB-25/DB-9 connector of

the short haul modem.

3. Connect the other end of the 3P-MF/3P-MF9 into the EIA-232 device.

The application should look similar to the diagram in Figure 1.

Figure 1. Connecting a Model 3P-MF

4. Plug the wall-adapter into the AC wall jack.

5. Connect the twisted pair line connection between short haul modems

as described in the short haul modem user manual (see Figure 2,).

Figure 2. Powering up a Self-Powered Short Haul Modem with a Model 3P-MF

APPENDIX A

PATTON MODEL 3P-MF & 3P-MF9 SPECIFICA

TIONS

A.1 TRANSMISSION FORMAT

Asynchronous

A.2 ELECTRICAL INTERFACE

• Model 3P-MF: EIA-232

• Model 3P-MF9: EIA-574

A.3 DATA RATE

Transparent to Data Rate

A.4 DTE/DCE CONNECTION

Either a male or female DB-25

A.5 CONNECTORS

• Model 3P-MF: DB-25M and DB-25F

• Model 3P-MF9P: DB-9M and DB-9F

A.6 POWER SUPPLY

120 or 230 VAC wall mount adapter supplies 9 VDC

A.7 MAX. POWER OUTPUT

+9 VDC ±5% at 100mA (approx 945 mW)

A.8 SIZE

• Model 3P-MF9: 2.7 x 1.2 x 0.7 in. (6.9 x 3.0 x 1.8 cm)

• Model 3P-MF: 2.2 x 2.1 x 0.7 in. (5.6 x 5.3 x 1.8 cm)

A.9 COMPLIANCE INFORMATION

• FCC Part 15, Class A

• UL/CSA (120VDC Wall Mount)

• EN55022 Class A (Emissions)

• EN50082-1 (Immunity)

• 89/336/EEC (Declaration of Conformity—Wall Mount)

• 73/23/EEC (Declaration of Conformity)

APPENDIX B

PATTON MODEL 3P-MF & 3P-MF9 PIN ASSIGNMENTS

Model 3P-MF DB-25 Interface

SIGNAL/PIN#

Secondary Transmit Data - 14

Transmit Clock - 15

1 - (FG) Frame Ground

2 - (TD) Transmit Data

Secondary Receive Clock - 16

Receiver Clock - 17

3 - (RD) Receive Data

4 - (RTS) Request to Send

5 - (CTS) Clear to Send

6 - (DSR) Data Set Ready

7 - (SG) Signal Ground

8 - (CD) Carrier Detect

9 - (DCV+) DC Test Voltage*

10 - (DCV-) DC Test Voltage

11 - Unassigned

Local Loopback - 18

Secondary Request to Send - 19

Data Terminal Ready - 20

Remote Loopback - 21

Ring Indicator - 22

Data Signal Rate Selector - 23

Transmit Clock - 24

Test Mode - 25

12 - Secondary Rcvd Line

13 - Secondary Clear to Send

* Note Model 3P-MF applies power to pin 9 (DCV+) only. All other sig-

nals are passed through unmodiﬁed from end-to-end. Signal

names are provided here to more closely represent the EIA-232

standard (see Appendix C on page 8).

Model 3P-MF9 DB-9 Interface

SIGNAL/PIN#

1- (CD) Carrier Detect

Data Set Ready (DSR) - 6

Ready to Send (RTS) - 7

Clear to Send (CTS) - 8

*DC Test Voltage (DCV+)- 9

2 - (RD) Receive Data

3 - (TD) Transmit Data

4- (DTR) Data Terminal Ready

5- (SG/FG) Signal Ground/ Frame Ground

* Note Model 3P-MF9 applies power to pin 9 (DCV+) only. All other sig-

nals are passed through unmodiﬁed from end-to-end. Signal

names are provided here to more closely represent the EIA-232

standard (see Appendix C on page 8).

APPENDIX C

PATTON MODEL 3P-MF BLOCK DIAGRAM

APPENDIX C - (CONTINUED)

PATTON MODEL 3P-MF9 BLOCK DIAGRAM

Power can be provided through pin 9 (default setting), DSR, or RTS by

changing jumper settings (see Table 1).

Table 1: Power Output Strap Selection

Jumper

Description

JP-1

JP-2

JP-3

JP-4

Connect 9 VDC to male connector (Default setting)

Connect 9 VDC to DSR

Connect pin 9 of male and female connectors

Connect 9 VDC to RTS

Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do appreciate

your business. I trust that you ﬁnd this user manual helpful.

We manufacture one of the widest selections of data communications

products in the world including CSU/DSU's, network termination units,

powered and self-powered short range modems, ﬁber optic modems,

interface converters, baluns, electronic data switches, data-line surge

protectors, multiplexers, transceivers, hubs, print servers and much

more. We produce these products at our Gaithersburg, MD, USA, facility,

and can custom manufacture products for your unique needs.

We would like to hear from you. Please contact us in any of the following

ways to tell us how you like this product and how we can meet your prod-

uct needs today and in the future.

Web:

http://www.patton.com

[email protected]

Sales E-mail:

Support E-mail:

Phone - Sales

Phone - Support

Fax:

[email protected]

(301) 975-1000

(301) 975-1007

(301) 869-9293

Mail:

Patton Electronics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton Electron-

ics is BABT and ISO 9001 certiﬁed. We meet and exceed the highest

standards in the industry (CE, UL, etc.).

It is our business to serve you. If you are not satisﬁed with any aspect of

this product or the service provided from Patton Electronics or its distrib-

utors, please let us know.

Thank you.

Burton A.Patton

Vice President

P.S. Please tell us where you purchased this product:

_________________________________________________________

Notes

_________________________________________________________

Patton Electronics Company

Murphy Switch EVS S User Manual
Murray Lawn Mower 425620x92B User Manual
NEC IP Phone 4 User Manual
OK International Water Dispenser TS250 User Manual
Omega Thermostat CN3440 User Manual
Omega Vehicle Security Power Supply IP210 User Manual
Optimus Stereo System 13 1288 User Manual
Oreck Vacuum Cleaner U3640RH User Manual
Panasonic Camera Lens LX025 User Manual
Panasonic Telephone KX TA616 User Manual