®
S I M P L Y
A M A Z I N G
USER’S GUIDE
U2640RH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Warranty
Troubleshooting Guide
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company
gives you the following limited warranty for this product only if it was origi-
nally purchased for residential use, not resale, from Oreck or an Oreck
Authorized Retail Dealer.)
WARNING: Unplug cord from electrical
outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
Oreck will repair or replace, free of charge, to the original purchaser, any
part which is found to be defective in material or workmanship within three
(3) years of the date of purchase; ten (10) years on housing. This limited
warranty applies to normal domestic use. Any commercial use of this
product will void this limited warranty. This limited warranty covers the
revolving roller brush for one (1) year for residential use only.
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive
belts, bulbs, disposable bags and other parts subject to normal wear
unless they are defective in material or workmanship.
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
PROBLEM
POSSIBLE SOURCE
AREAS TO CHECK
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of God,
the use of voltages other than indicated on the serial number displayed on
this product or service of this product by other than Oreck or a participating
Factory Authorized Service Center.
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
CLEANER
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
Oreck does not authorize any person or representative to assume or grant
any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag.
See “To Replace
Paper Filter Dust Bag.”
Nozzle or intake
pivot clogged.
Clear obstruction.
Belt is broken or
stretched.
Replace belt.
Oreck’s liability for damages to you for any costs whatsoever arising out
of this statement of limited warranty shall be limited to the amount paid for
this product at the time of original purchase, and Oreck shall not be liable
for any direct, indirect, consequential or incidental damages arising out of
the use or inability to use this product.
Brush is worn.
See “To Replace or
Adjust Brush.”
Clear obstruction.
Change bag.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to
you.
Bag tube clogged.
Bag pores are
clogged with fine
dust.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Return to Service
Center for repair.
Impeller fan is
broken.
Check brush roll end
cards. Make sure
words “OLD” or
“NEW” match at
each end.
Revolving brush is
not even at both
ends.
Some states do not allow limitations on the duration of implied warranties,
so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535 Canada: 1-888-676-7325
Whenever calling, please be sure to have your model and serial
number from data plate.
3
1
2
3
4
5
Upper Handle
Connector Assembly
6
7
8
9
10
15
20
25
NJUSQU’À
ENTENDRE UN BRUIT
HASTA
ESCUCHAR UN
DE SUJECIÓN
11
16
21
26
12
17
22
27
13
18
23
14
19
OLD
NEW
24
Tube
Fan Housing
Retainer
Spring
O-ring
Intake Opening
Intake Opening
28
Fan Housing
Connector
Deflector
Opening
4
4. Although your upright will pick up pins, paper clips, and other
small objects, it is recommended that these be removed from the
floor before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
Parts List
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
10
1
2
3
4
5
6
7
8
9
Handle section, upper
Tube, lower
Power head
Outer bag
Paper filter dust bag
Power cord
Retaining spring
Bag tension bar
Zip fastener
11
9
1
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
12
5
4
8
10 On/off switch
11 Cord hook
12 Connector assembly
13 Fan housing
9. Use caution when vacuuming over area rug edges and fringe.
2
6
General Information
14 Cord assembly
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
13
7
14
3
Disposable Paper Filter Dust Bags
Assembly
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the paper
bag is to trap dirt, but at the same time it must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and cleaning cannot take place, regardless of
the cleaner’s power.
fig. 1 Before assembling appliance, remove screws from the connector
assembly. Remove cardboard insert by pulling upward.
fig. 2 With ON/OFF switch facing the front of the unit, slide upper
handle section over matching section of the connector assembly.
Insert short screw into top hole and long screw into the bottom
hole then tighten firmly until handle is no longer loose.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
fig. 3 Attach cord to cord clip by pressing cord above and below clip
Be sure the disposable paper filter dust bag is installed properly.
ensuring the cord is fully rested in clip.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
Operating Instructions
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the ON(l) - OFF(O) switch on handle
assembly when ready to operate.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
Up-Position Lock
fig. 4 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than ORECK belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
For Easy Power Cord Storage
fig. 5 Wrap power cord around cord hook on handle and cord hook on
Lubrication
connector. Secure cord to "U" shaped part on plug.
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
General Cleaner Care
At least once a month, check for and
remove excessive lint, string or hair from
revolving brush.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
Wipe the outside of the cleaner with a
damp cloth. Also clean the connector
deflector assembly area, base of cleaner
and fan housing area. If there is dust in
the outer bag, vacuum it or shake it out.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
A little preventative maintenance will keep
your cleaner looking new and will ensure
continued cleaning effectiveness.
5
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
IMPORTANT: Unless the brush is worn as indicated above, both
bearings must be in the “NEW” position. When rotating, both
bearings must be in the “OLD” position. Unmatched settings will
cause damage to your machine.
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
®
Using An Oreck Fresh Air Tab
fig. 20 Your ORECK XL vacuum cleaner has a special ORECK FRESH
AIR® tab pocket. This pocket is located inside the outer bag in
the area where the paper disposable bag attaches to the intake
tube. Insert tablet in pocket if desired.
To Replace Filter Dust Bag
Stuffing or Blockage
WARNING: Unplug cord from electrical
outlet before servicing.
IMPORTANT: On plush and new carpets, stuffing may occur inside the
the intake tube and the lower tube assembly. This is due to excessive fuzz
and loose cuttings in the carpet. Stuffing could occur for the first few
cleanings until all the loose material is removed. Due to the high efficiency
of the cleaner, many older carpets will cause stuffing when the cleaner is
first used on them. If your vacuum cleaner does not pick up properly, or
makes unusual noise and the outer bag does not fluff up or balloon open,
follow these steps:
BAG REMOVAL:
fig. 6 Unzip outer bag completely.
fig. 7 Pull bag cardboard collar to release bag dock door from
connector. Bag dock door will hinge downward.
fig. 8 Gently pull bag cardboard collar upward out of the bag dock.
The dust seal will close automatically.
WARNING: Unplug cord from electrical
outlet before servicing.
BAG INSTALLATION:
fig. 9 Slide the cardboard collar completely onto bag dock door.
fig. 21 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove
baseplate (fig. 22).
fig. 10 Firmly push bag dock door with both thumbs on indication point
until it snaps.
fig. 23 If the blockage is not at the base, remove lower tube. Unhook
How to Replace a Worn Belt
retainer spring, releasing bottom of bag.
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 24 Twist lower collar counterclockwise to slide up. Pull tube out of
base.
fig. 25 Check for blockage. If blockage is in the tube, remove with a
fig. 11 Remove the replacement belt from the storage channel.
coat hanger.
fig. 12 Remove the door by removing the hold down screw located on
fig. 26 If tube is not blocked, look into fan housing. Remove debris
side of power head.
with long-nose pliers, a screwdriver or coat hanger.
fig. 13 Slide the door forward by prying open with a screwdriver or coin.
fig. 24 To reassemble, check O-ring on tube, and replace if damaged.
Vacuum will not operate properly without the tube O-ring. Slide
O-ring to approximately 2" from base of tube. Replace tube by
first lining up slot at base of tube with inner tab inside fan
housing. Then reinsert tube and push down until the tube is
seated. Make sure O-ring is in place against fan housing
opening. Replace and tighten collar until collar locking tabs are
locked in place.
fig. 14 Remove the belt from the brush roll pulley and motor drive shaft.
fig. 15 Loop the new belt over the motor drive shaft. Place the opposite
end of the belt on the brush roll pulley. Rotate the brush roll
three (3) complete revolutions to ensure that no part of the belt
is overhanging the end of the motor drive shaft.
fig. 13 Replace the door by sliding it into the groove at the bottom of
the housing.
fig. 27 Make sure collar is not cross threaded on housing. Reattach
fig. 12 Replace the hold down screw and tighten.
bag spring (fig. 23).
To Adjust or Replace Brush
fig. 28 Many times blockage occurs due to a full dust bag causing dirt to
back down the air flow system. When that happens, the
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 16 To determine if the brush is worn, place a firm straight edge
across the nozzle opening. If brush bristles do not extend
beyond baseplate, brush should be adjusted.
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
NOTE: If the above actions do not correct the problem, contact an
Oreck authorized service center or call the customer service center.
US: 1-800-989-3535 Canada: 1-888-676-7325
fig. 17 Remove the baseplate by removing 5 screws.
fig. 18 Remove the belt and brush roll from the housing.
fig. 19 Rotate both bearing assemblies at ends of brush roll to show
"OLD" and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked "OLD" has no ribs on the
top of the assembly. The one marked "NEW" has several ribs. When
rotating bearings, make sure both bearing assembly settings are the
same and face up when replacing the brush roll.
fig. 16 Reassemble the belt and the baseplate and check bristle height
above baseplate at each end of brush.
If a previous adjustment has already been made and bristle height does
not extend above baseplate, a new brush assembly should be ordered.
6
7
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. Printed in America
75718-02 REV B
05/05 ECN# R-8018
|