Model VT-1.2
Audio / Video Tower Loudspeaker
OWNER’S MANUAL
Now Hear This
6400 Goodyear Road
Benicia, CA 94510
800-NHT-9993
„
Placement
The Model VT-1.2 is a floorstanding loudspeaker that requires no stands or mounting hardware other than the included
SpikeKit. The VT-1.2 is designed for indoor use only.
For best results, the VT-1.2’s are best situated at least six inches from the rear wall (due to the rear vent) and at least one
foot from the side walls. The speakers should be arranged as symmetrically as possible so that the drivers face the
listening area without obstruction from furniture. With the VT-1.2’s set up properly, the side-firing woofers face to the
outside (away from the TV) and the tweeters are at approximately ear level. If possible, arrange the speakers so that the
distance between the listener and the center of the speaker plane is about 1.5 times the distance between the two speak-
ers (fig. 2). This configuration puts the listener in the center of the stereo image.
The upper portion of the VT-1.2 features magnetically shielded drivers, allowing the speakers to be placed in close prox-
imity to a television without causing picture discoloration. Ideally, the three front speakers in a home theater system should
be placed at equal height, equidistant, and at ear level from the listening position. However, it is frequently not possible to
install a center speaker at ear level, as the top surface of most televisions tends to be higher than ear level in the seated
position. In this case, it is advantageous to tilt or aim the center speaker toward the listening position.
Experimentation is the key to finding the best arrangement in your listening environment. Be patient, have fun, and remem-
ber that small changes in speaker position can sometimes have a significant effect on the sound. For example, moving
the speakers nearer to a room boundary (walls, corners) will tend to increase their bass output, but may result in “boomy”
or “muddy” sound. Conversely, placing the speakers farther away from room boundaries will tend to decrease their bass
output, but may result in greater articulation and better imaging.
In addition, room furnishings play an important role in absorbing and reflecting soundwaves. Midrange and high frequen-
cies in particular will be absorbed by soft furnishings such as sofas, carpets and curtains. A large number of these soft
furnishings will dull the sound, while a “live” room with few furnishings will brighten the sound. If you are willing to spend
fig. 3
fig. 2
some time fine-tuning the performance of your system, you will enjoy the benefits for years to come.
„
SpikeKit Installation
A SpikeKit is included with the Model VT-1.2 to provide optimum stability and to firmly couple the speakers to the floor for
improved bass performance. Each VT-1.2 loudspeaker is shipped with its own SpikeKit. Caution: the VT-1.2 is unstable
without the SpikeKit (or at least the stabilizer bars) installed.
To begin assembly, unpack the SpikeKit and inspect all the parts. The SpikeKit includes: (2) stabilizer bars, (4) metal
spikes, (4) Phillips head machine screws, (4) lock nuts and (4) rubber feet. We recommend installing the spikes only after
you have found the ideal location for the speakers. Begin by installing the stabilizer bars. Carefully turn the speaker upside
down or on its back and attach the stabilizer bars with the Phillips head machine screws, using a #2 Phillips screwdriver
(fig. 3). Note: When installing the bars onto the bottom of the speaker, use your fingers to start all the machine
3
screws in their holes before tightening them down. This will prevent crossthreading.
Before installing the spikes, turn the speakers upright and position them. When you have found the perfect spot, careful-
ly tilt the speakers and screw in the spikes with the lock nuts on them. The speakers are awkward to move after the spikes
are installed. Caution: The spikes are very sharp. To avoid injury, use extreme care when handling and installing
them. Adjust the spikes as needed to ensure that the VT-1.2 is level and does not rock in any direction. Tighten then lock
nuts against the bottom of the stabilizer bar to lock the spikes in place. If you have hardwood floors or floors with a scratch-
able surface, you may choose not to use the spikes because they will pierce the surface. Rubber feet are provided and
can be used in place of the spikes. Install the stabilizer bars, peel off the adhesive backings from the rubber feet, and
place them over the holes where the spikes would screw in.
„
Connections
Before connecting speakers to your system, it is very important that you turn off the power to your amplifier /
receiver to avoid damage to the equipment.
On the back panel of the VT-1.2 there are two sets of binding posts (fig. 4) with a metal jumper strap connecting the top
and bottom posts. There are three different ways to connect the VT-1.2’s to your system: Full-range with a single amplifi-
er / receiver, Bi-amplified with two amplifers and two sets of speaker wire, or Bi-wired with one amplifier and two sets of
speaker wire. To run the VT-1.2’s full-range with one amplifier / receiver, simply connect the speaker wires to either the
top set or bottom set of posts (it doesn’t matter which one).
Bi-amplification is the use of two separate amplifiers, one to power the bass drivers and one to power the midrange / high frequency
drivers. This configuration provides greater dynamic range for both amplifiers, as they are spared the task of reproducing the entire
frequency range. In addition, bi-amplification is a great advantage in home theater systems, as it turns the passive subwoofer sec-
tion of the VT-1.2 into a powered subwoofer. NHT’s SA-2 and SA-3 subwoofer amplifiers are optimized for subwoofer amplifica-
tion and feature adjustable volume and bass tuning functions, which allow the user to fine-tune bass response for an individual lis-
tening environment.
Note: It is very important that you remove the jumper straps when bi-amplifying or you will damage your amplifiers! To
bi-amplify the VT-1.2, you will need two amplifiers, one for the upper range drivers (top pair of binding posts) and one for the sub-
woofer (bottom pair). Connect one pair of binding posts with speaker wire from one amplifier, and the other pair of binding posts
with speaker wire from the second amplifier. If you have an audio / video receiver, you may use its front left and right speaker out-
puts to drive the upper section, and a separate amplifier for the subwoofers. It is important to achieve level matching between the
two amplifiers. Use either two identical amplifiers, or make sure that one amplifier has a volume control. Both amplifiers will need
to receive an identical line-level signal from the preamplifier/processor or “pre-out” jacks of the A/V receiver. If only one set of “pre-
out” jacks are available, use a “Y” splitter in order to send the signal to both amplifiers. For more detailed information about bi-
amplification, contact your local authorized NHT retailer.
Some audio enthusiasts have found that
bi-wiring can
fig. 4
bring about improvements in sound. Bi-wiring is the use of
two pairs of speaker wire and one amplifier, with each pair
connected to one set of binding posts on the amplifier
(some two-channel amplifiers provide two sets). To bi-wire
the VT-1.2’s, connect the top pair of binding posts to the
amplifier with one speaker wire, and the bottom pair
with a second wire. The two sets of speaker wire are
both connected to one pair of terminals on the amplifi-
er.
The Model VT-1.2 loudspeaker system is compatible
with virtually all quality amplifiers. Proper wiring of the
speakers is essential to good sound. At a minimum,
14AWG wire is recommended for runs of 10 feet or less,
with heavier special purpose speaker wire used for
longer runs. For specialty wire considerations, consult
your local authorized NHT retailer. For best results, use
equal length runs of speaker wire for the left and right
speakers. Prepare your speaker wire by stripping 1/4” to 3/8” of insulation from the ends and twisting the exposed wire
strands tightly. The five-way binding posts on the back of the speaker will accept raw wire, banana plugs, or spade plugs.
Tighten the binding posts by hand, as pliers can strip or break them.
Be sure to wire both the left and right speakers "in-phase." That is, the Positive (red) terminal on the amplifier
output must be connected to the corresponding Positive (red) terminal on the speaker. Likewise with the Negative
(black) terminals. All speaker wires have some sort of marking along one or both conductors to help you make the cor-
rect connections. Incorrect speaker phase is indicated by weak bass and the lack of a well-defined stereo image.
To minimize noise pickup, segregate cables by function. Do not run low level signal cables parallel to power cables, speak-
er cables, or digital cables. Also, do not run speaker cables or digital cables parallel to power cords or parallel to each
4
other. If different types of cables are placed near each other at some place in your system, separate them by the maxi-
mum practical distance and cross them at right angles where they meet. Do not twist or tie AC power cords with speaker
cables.
„
Operation
The Model VT-1.2 was designed to handle a wide range of listening levels, but every speaker has limits. It is important to
use common sense and listen for signs of possible distress from the speakers. Underpowered amplifiers are most often
the cause of speaker damage. For example, a 60-watt amplifier runs out of power when called upon to produce more than
60 watts, and the resulting distortion can damage the speaker. If you tend to listen at high volume levels, more powerful
amplifiers are preferable becase they are less likely to run out of power.
Noticeable distortion or harsh breakup is an indication that either your amplifier or your speakers are running beyond their
capacity, and the volume should be decreased. If you can feel any heat emanating from the woofer or tweeter, reduce the
level immediately. Speaker damage most often occurs from sustained high volume levels, not from transient sounds or
brief musical peaks. Excessive boosting of bass, treble or equalizer controls can worsen the problem, and is not recom-
mended.
„
Maintenance
Your speakers require minimal maintenance under normal use. The cabinet may be cleaned using a damp cloth or a mild,
non-abrasive cleaner. To clean the grille, first remove it from the speaker, then brush lightly with a soft brush or use a vac-
uum on its lowest setting. Do not expose the speakers to direct sunlight, high temperatures, or moisture. Do not attempt
to clean the actual drivers.
Warranty
Valid Only in the U.S.A.
Warranty Period
For the period of 5 years for parts and 5 years for labor from date of original purchase (the warranty period) from an authorized NHT
dealer, Now Hear This (NHT) warrants that if our product fails to function properly under normal use due to a manufacturing defect
when installed and operated according to the owner’s manual instructions enclosed with the unit, it will be repaired or replaced with
a unit of comparable value at the option of NHT without charge to you for parts or actual repair work. Parts supplied under this
ranty may be new or rebuilt at the option of NHT.
war-
What’s Not Covered
This warranty does not cover any product which is used in any trade or business, or in an industrial or commercial application.
This warranty does not cover the cabinet or any appearance item, or any damage caused to the product resulting from: alterations,
modifications not authorized in writing by NHT, accident, misuse or abuse, damage due to lightning or power surges, or being
subjected to power in excess of the speaker’s published power rating.
This warranty does not cover the cost of parts which would otherwise be provided without charge under this warranty, obtained from
any source other than an authorized NHT service location. This warranty does not cover defects or damage caused by the use of
unauthorized parts or labor or from improper maintenance.
Altered, defaced or removed serial numbers void this warranty.
Your Rights
The liability of NHT will be limited to the purchase price of the product, and NHT will not be liable for incidental or consequential
damages. NHT limits its obligations under any implied warranties under state laws to a period not exceeding the warranty period.
Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation
of incidental or consequential damages. The above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may have other rights which vary from state to state.
To Obtain Service
NHT has appointed a number of authorized service companies throughout the USA should your product ever require service. To
receive warranty service, you will need to present your sales receipt showing place and date of original owner’s transaction.
To find the name and address of the nearest authorized NHT service location, call or write: Customer Service Department, Now
Hear This, 6400 Goodyear Road, Benicia, CA 94510. 800-NHT-9993.
Please do not return product to this address. It is not a service location.
Keep this warranty with your sales receipt.
Record date and place of purchase for future reference.
5
|